Siemens SIMATIC MP 270B Operating Instructions Manual Download Page 51

Page: 51 / 274

Installation and connection

4.3 Connecting the HMI device

TP 270, OP 270, MP 270B (WinCC flexible)
Operating Instructions, Edition 03/2004, 6AV6691-1DD01-0AB0

4-13

4.3.5

Connecting the PLC

Connection configuration

The figure below illustrates the basic connection possibilities between the HMI device and

PLC. Standard cables are available for the connections shown (refer to the ST80 catalog).

RS 232

(9/25-pin)

RS 422

(9-pin)

RS 232

PLCs of other

manufacturers

RS 422

RS 422/RS 485

SIMATIC 505

SIMATIC S7

RS 232

IF1A

IF1B

RS 485

Operating unit

PROFIBUS-DP

Figure 4-5

Connection configuration for PLCs

•

SIMATIC S7
Use only the approved cables for connection to a SIMATIC S7.

•

IF1A / IF1B
To enable communication using the serial interface, connect either the IF1A (RS 232) or

IF1B (RS 422/485), but not both. The 1F1B interface can be configured using a switch.

•

PROFIBUS DP
Any PROFIBUS-DP bus terminal can be used.

Summary of Contents for SIMATIC MP 270B



















































































































































































































































































Search results

Summary of Contents for SIMATIC MP 270B

Reviews:

Brands by name

Popular brands

Siemens SIMATIC MP 270B, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC MP 270B

Reviews:

Brands by name

Popular brands