Siemens SIMATIC MP 270B Operating Instructions Manual Download Page 44

Page: 44 / 274

Installation and connection

4.3 Connecting the HMI device

TP 270, OP 270, MP 270B (WinCC flexible)

4-6

Operating Instructions, Edition 03/2004, 6AV6691-1DD01-0AB0

4.3.2 Interfaces

Interfaces

The figure below illustrates the arrangement of the interfaces on underside of the HMI

device, exemplified by the MP 270B 10" Keys.

Notice
In the case of the TP 270 and OP 270, the interfaces for the PC card and Ethernet interface

on-board are missing. To enable an Ethernet connection, the devices require a CF card.

Figure 4-1

Arrangement of the interfaces (example, MP 270B 10" Keys)

No. Description

Application

Ground connection

For connection to rack ground

Power supply

Connection to power 24 V DC)

Interface IF1B

RS 422/RS 485 (floating) for PLC, PC, PU

Interface IF1A

RS 232 for PLC

Interface IF2

RS 232 for PC, PU, printer

Switch

To configure interface IF1B

Battery connection

Connection for optional backup battery

USB interface

Connection for external keyboard, mouse, etc.

Slot B

For CF card

10 Ethernet

interface

(for MP 270B only)

Connection of an RJ45 Ethernet line

11 Slot A

(for MP 270B only)

For PC card

Summary of Contents for SIMATIC MP 270B



















































































































































































































































































Search results

Summary of Contents for SIMATIC MP 270B

Reviews:

Brands by name

Popular brands

Siemens SIMATIC MP 270B, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC MP 270B

Reviews:

Brands by name

Popular brands