manualshive.com logo in svg

Siemens SIMATIC MP 270B, Operating Instructions Manual

Share
Download
Siemens SIMATIC MP 270B Operating Instructions Manual Download Page 36

Plan deployment 

 

3.4 Producing the installation cut-out 

 

TP 270, OP 270, MP 270B (WinCC flexible) 

3-4

 

Operating Instructions, Edition 03/2004, 6AV6691-1DD01-0AB0 

Ambient conditions 

 

 

Caution 
If the maximum permissible ambient temperature is exceeded, do not operate the HMI 

device without external ventilation.  
Otherwise, the HMI device may be damaged and the approvals listed in the Section 

"Approvals" and the terms of warranty are void. 

See also 

Approvals (Page A-1) 
Technical data (Page 12-5) 

3.4 

Producing the installation cut-out 

Select position for the installation cut-out 

 

 

Caution 
To prevent the HMI device from overheating during operation:  
- The angle of inclination from vertical installation may not exceed a maximum of 

±

35

°

  

- Do not expose the operating unit to direct sunlight  
- Ensure that the ventilation slits in the housing are not obstructed  

 

 

Summary of Contents for SIMATIC MP 270B



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands