manualshive.com logo in svg

Siemens SIMATIC MP 270B, Operating Instructions Manual

Share
Download
Siemens SIMATIC MP 270B Operating Instructions Manual Download Page 170

Operate project 

 

9.2 Controlling graphic objects 

 

TP 270, OP 270, MP 270B (WinCC flexible) 

9-44

 

Operating Instructions, Edition 03/2004, 6AV6691-1DD01-0AB0 

9.2.13.4  Mouse and keyboard control 

Procedure 

Mouse 

Click the slider control. Move the slider control in the desired direction while holding down 

the mouse button.  

Keyboard 

Activate the trend view with <Tab>, using the tab order configured.  
You can operate the slider with the following keys: 

 

Key 

Key (Panel PC) 

Function 

<Up> or <Right> 

<Shift+Up> or <Shift+Right> 

Increase value 

<Down> or <Left> 

<Shift+Down> or <Shift+Left> 

Reduce value 

<Page up> 

-- 

Increase value in 5% increments  

<Page down> 

-- 

Reduce value in 5% increments 

<Home> 

-- 

Set maximum value 

<End> 

-- 

Set minimum value 

9.2.14 Gauge 

Purpose 

The gauge is a dynamic display object. The gauge displays numeric values in analog form 

by means of a pointer. For example, the operator at the HMI device can thus see at a glance 

that the boiler pressure is in the normal range.  

 

Summary of Contents for SIMATIC MP 270B



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands