manualshive.com logo in svg

Siemens SIMATIC IPC677E, Operating Instructions Manual

Share
Download
Siemens SIMATIC IPC677E Operating Instructions Manual Download Page 37

 

Mounting and connecting the device 

 

3.1 Preparing for mounting 

SIMATIC IPC677E 
Operating Instructions, 04/2019, A5E45117996-AA 

37

 

3.1.4

 

Mounting positions 

 

 

NOTICE 
"Open Equipment" IEC/EN/UL61010  
The device is designed for use as a programmable controller, OpenType according to 

IEC/EN/UL 61010-2-201. The installation of the device in a fire protection housing in 

accordance with IEC/EN/UL 61010-2-201 is therefore a mandatory requirement for 

approval or operation. 

 

The following mounting positions are permitted for the device. 
For information on the maximum permissible ambient temperatures during operation, refer to 

section "Ambient conditions (Page 115)". 

Mounting positions according to UL61010 

 

 

Note 
Operation in closed rooms 
The device is approved for operation in closed rooms only. Note the Ambient conditions 

(Page 115). 

 

Mounting in horizontal format 

 

 

 

Note 
Mounting precautions 

•

 

The total power for USB and PCI/PCIe expansions cannot exceed 30 W. 

 

Summary of Contents for SIMATIC IPC677E































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands