Siemens SIMATIC IPC677E Operating Instructions Manual Download

Page: 17 / 158

Product description

1.4 External design of the device

SIMATIC IPC677E
Operating Instructions, 04/2019, A5E45117996-AA

1.4.2

Side view, left

Connection side

①

On/off button

The on/off button has three functions:

•

Switch on the PC: Briefly press once

•

Shut down operating system and switch off PC: Briefly press once

•

Switch off PC without shutting down the operating system (hardware reset): Press for more

than 4 seconds.

Note: The BIOS setup entry "After Power Failure" has been set to "Power On". This means the

device is switched on with the on/off switch. You then do not need to press the on/off button.

②

4 status LEDs

Status display of the status indicators (Page 19)

③

COM1 X30

Serial interface

④

DVI/VGA X70

DVI-D connection for CRT or LCD monitor with DVI port

⑤

DisplayPort

X71/X72

DisplayPort connection for digital monitor

⑥

3 × Ethernet

X1P1/X2P1/X3P1

•

X1P1, left: RJ45 Ethernet port 1 (exclusive PCI interrupt) with 10/100/1000 Mbps, iAMT ca-

pable

•

X2P1, center: RJ45 Ethernet port 2 (shared PCI interrupt) with 10/100/1000 Mbps

•

X3P1, right: RJ45 Ethernet port 3 (shared PCI interrupt) with 10/100/1000 Mbps

Summary of Contents for SIMATIC IPC677E































































































































































Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands

Siemens SIMATIC IPC677E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands