Siemens SIMATIC IPC677E Operating Instructions Manual Download

Page: 148 / 158

Markings and symbols

C.4 Certificates, approvals and markings

SIMATIC IPC677E

148

Operating Instructions, 04/2019, A5E45117996-AA

C.4

Certificates, approvals and markings

The following table shows symbols relating to certificates, approvals and markings which

may be on the device. You can find more information in the operating instructions for your

device:

Symbol

Meaning

Symbol

Meaning

Approved for Australia and New Zea-

land

Marking for the Eurasian Customs

Union

Approved for China

Test mark of Factory Mutual Re-

CE markings for European countries

Marking of Federal Communications

Commission for the USA

EFUP (Environment Friendly Use

Period) marking for China

Approved for Korea

Test mark of the Underwriters La-

boratories

Disposal information, observe the

local regulations.

Approval for India

Summary of Contents for SIMATIC IPC677E































































































































































Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands

Siemens SIMATIC IPC677E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands