Siemens Simatic IPC520A Operating Instructions Manual Download Page 73

Page: 73 / 80

SIMATIC IPC520A
Operating Instructions, 11/2021, A5E51366325-AA

Markings and symbols

C.1

Overview

The following tables show all the symbols which may be found on your SIMATIC industrial PC,

SIMATIC industrial monitor or SIMATIC Field PG in addition to the symbols which are

explained in the operating instructions.
The symbols on your device may vary in some details from the symbols shown in the

following tables.

C.2

Safety

Symbol

Meaning

Symbol

Meaning

Warning, observe the supplied

documentation.

Lock is closed

Attention, radio equipment

Lock is open

Disconnect the power plug before

opening

Opening for Kensington lock

Attention ESD (Electrostatic sensitive

device)

Warning of hot surface

C.3

Operator controls

Symbol

Meaning

Symbol

Meaning

On/off switch, without electrical

isolation

Eject CD/DVD

On/off switch, without electrical

isolation

Summary of Contents for Simatic IPC520A

















































































Search results

Summary of Contents for Simatic IPC520A

Reviews:

Brands by name

Popular brands

Siemens Simatic IPC520A, Operating Instructions Manual

Search results

Summary of Contents for Simatic IPC520A

Reviews:

Brands by name

Popular brands