Siemens Simatic IPC520A Page 58 Operating Instructions Manual Download

Page: 58 / 80

Technical specifications
7.8 Hardware descriptions

SIMATIC IPC520A

Operating Instructions, 11/2021, A5E51366325-AA

7.8.2

External Interfaces

7.8.2.1

Overview of external interfaces

Interface

Position

Description

USB

External

• 1 × USB 2.0 Micro B (X64)
• 3 × USB 3.0 Type A (X60, X61, X62)

Ethernet port

External

• 2 × Gbe RJ45 (X3) Dual channel
• 2 × Gbe RJ45 (X1) and RJ45 (X2) (with Addition POE

Function)

DisplayPort (X70)

External

• 1 × DP

COM (X30)

External

• RS232, max. 115 Kbps, D-sub connector, 9-pin
• RS422, max. 115 Kbps, D-sub connector, 9-pin
• RS485, max. 115 Kbps, D-sub connector, 9-pin

Digital I/O Connector

(X10)

External

• 4 × DI + 2 × DQ

7.8.2.2

Power supply

Plug connector, 2-pin

Name of interface on the device: X1080

Pin

Assignment

GND (M)

DC 24 V (19.2 to 28.8 V DC) (L+)

Summary of Contents for Simatic IPC520A

















































































Search results

Summary of Contents for Simatic IPC520A

Reviews:

Related manuals for Simatic IPC520A

Brands by name

Popular brands

Siemens Simatic IPC520A, Operating Instructions Manual

Search results

Summary of Contents for Simatic IPC520A

Reviews:

Related manuals for Simatic IPC520A

Brands by name

Popular brands