Siemens Simatic IPC520A Operating Instructions Manual Download Page 41

Page: 41 / 80

Expanding the device

5.2 Inserting the Micro SD card/Nano SIM card

SIMATIC IPC520A
Operating Instructions, 11/2021, A5E51366325-AA

5.2

Inserting the Micro SD card/Nano SIM card

Requirements

•

The device is disconnected from the power supply.

•

Micro SD card or Nano SIM card that is suitable for industrial use.

Installation

NOTICE
Inserting a memory card

If you are using the Micro SD card/Nano SIM card in a device installed in a system, you must

observe the safety regulations for work on electrical systems.
Carefully insert the Micro SD card/Nano SIM card into the card holder without applying

excess force.

Open the card cover on the bottom.

Push the Micro SD card/Nano SIM card correctly into the supporting

frame. The contacts of the Micro SD card/Nano SIM card must face

to the motherboard.

Push the card cover back.

Summary of Contents for Simatic IPC520A

















































































Search results

Summary of Contents for Simatic IPC520A

Reviews:

Brands by name

Popular brands

Siemens Simatic IPC520A, Operating Instructions Manual

Search results

Summary of Contents for Simatic IPC520A

Reviews:

Brands by name

Popular brands