manualshive.com logo in svg

Siemens Simatic IPC520A, Operating Instructions Manual

Share
Download
Siemens Simatic IPC520A Operating Instructions Manual Download Page 33

 

SIMATIC IPC520A 
Operating Instructions, 11/2021, A5E51366325-AA 

33

 

Installing OS and SDK components

 

4 

4.1

 

Flashing the Ubuntu Operating System 

Follow these steps to flash the Ubuntu Operating System: 

 

 

Note 

Operating System is not installed in new device. 

 

1.

 

Install NVIDIA SDK Manager on a local PC. For detailed installation procedures, refer to the 

NVIDIA website (

https://docs.nvidia.com/jetson/jetpack/install-jetpack/index.html

). 

2.

 

Set the IPC520A to Force Recovery Mode (RCM). 

–

 

2.1 Switch off the IPC520A. 

–

 

2.2 Connect the IPC520A to local PC through the micro USB cable. 

–

 

2.3 Keep pressing the Reset button. 

–

 

2.4 Switch on the IPC520A and wait for more than 3 seconds, then release the Reset 

button. 

–

 

2.5 Check whether the IPC520A is entering the RCM: Enter the commend “

lsusb

”, then 

the output returns should be like below: 

 Bus <xxx> Device <xxx>: ID 0955: <7e19> Nvidia Corp

 

 Otherwise, redo the step 2.  

3.

 

Start up NVIDIA SDK Manager, and register an NVIDIA account to log in to NVIDIA SDK 

Manager. 

 

 

Summary of Contents for Simatic IPC520A

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands