Siemens SIMATIC IPC1047 Operating Instructions Manual Download Page 44

Page: 44 / 136

Commissioning the device

4.4 Notes on different device configurations

SIMATIC IPC1047

Operating Instructions, 09/2018, A5E45118479-AA

Requirements for Adaptec Storage Manager software

The following requirements must be met before you use the software for the first time during

commissioning:

●

4 GB main memory

●

The operating system is restarted.

●

The operating system is password-protected.

●

same.

Data is backed up to two or three SAS or SATA hard disks. As a result, the system is able to

continue operation in the event of a defective hard disk or port connection problems, thereby

achieving high availability. The 4-port or 8-port variant can be used.
An optionally available hot-spare drive can further increase the availability of the system.

①

Connection for the SAS/SATA data cable

②

Connection for Zero Maintenance Module (ZMM)

Summary of Contents for SIMATIC IPC1047









































































































































Search results

Summary of Contents for SIMATIC IPC1047

Reviews:

Siemens SIMATIC IPC1047, Operating Instructions Manual, Page: 44 / 136

Search results

Summary of Contents for SIMATIC IPC1047

Reviews: