Siemens SIMATIC IPC1047 Operating Instructions Manual Download Page 37

Page: 37 / 136

Installing and connecting the device

3.3 Connecting the device

SIMATIC IPC1047
Operating Instructions, 09/2018, A5E45118479-AA

Operation in the USA and Canada
For the United States and Canada, a CSA or UL-listed power cable must be used. The

connector must be compliant with NEMA 5-15.
240 V voltage
Use a flexible cable with UL approval and CSA mark as well as the following features: SJT

model with three conductors, min. 18 AWG conductor cross-section, max. length 4.5 m, and

tandem grounded connector 15 A, min. 250 V.

Requirement

●

The device is fully disconnected from the line voltage, see section

"Switching on the device (Page 40)".

●

1 power supply cable

Procedure

1. Set the on/off switch

①

to position '0'.

This prevents an automatic starting of the

device when plugging in the power supply

cable.

2. Plug the power cable plug

②

into the power

outlet.

3. Plug the power cable plug into the power

outlet.

4. Set the on/off switch

①

to position 'I'.

The power LED to the left of the on/off switch and on the front panel of the device lights

up.

Summary of Contents for SIMATIC IPC1047









































































































































Search results

Summary of Contents for SIMATIC IPC1047

Reviews:

Siemens SIMATIC IPC1047, Operating Instructions Manual, Page: 37 / 136

Search results

Summary of Contents for SIMATIC IPC1047

Reviews: