manualshive.com logo in svg

Siemens SIMATIC IOT, Operating Instructions Manual

Share
Download
Siemens SIMATIC IOT Operating Instructions Manual Download Page 52

Technical specifications 

 

7.5 Hardware descriptions 

 

SIMATIC IOT2020, SIMATIC IOT2040 

52

 

Operating Instructions, 10/2016, A5E37656492-AB 

7.5.2.3

 

Ethernet port 

RJ45 socket 
Name of interface on the device: X1 P1 LAN, X2 P1 LAN 

 

 

Pin 

Short description 

Meaning 

1 

BI_DA+ 

Bidirectional data A+, input/output 

2 

BI_DA– 

Bidirectional data A–, input/output 

3 

BI_DB+ 

Bidirectional data B+, input/output 

4 

BI_DC+ 

Bidirectional data C+, input/output 

5 

BI_DC– 

Bidirectional data C–, input/output 

6 

BI_DB– 

Bidirectional data B–, input/output 

7 

BI_DD+ 

Bidirectional data D+, input/output 

8 

BI_DD– 

Bidirectional data D–, input/output 

 

 

LED 

Short description 

Meaning 

1 

LED 1 

Off: 10 Mbps 

Lit green: 100 Mbps 

2 

LED 2 

Off: Cable not connected 
Lights up yellow: Connection established 
Flashes: Data transfer active 

7.5.2.4

 

Serial port (only SIMATIC IOT2040) 

D-sub socket, 9-pin, with screw lock 
Name of interface on the device: X30 COM, X31 COM 

 

 

RS 232 
RS 422 
RS 485 

Summary of Contents for SIMATIC IOT

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands