manualshive.com logo in svg

Siemens SIMATIC Ident CB Gate, Operating Instructions Manual, Page: 67 / 70

Share
Download
Siemens SIMATIC Ident CB Gate Operating Instructions Manual Download Page 67

 

SIMATIC Ident CB Gate 
Operating Instructions, 08/2022, C79000-G8976-C671-01 

67

 

Appendix

 

A 

A.1

 

Order data 

Table A- 1 

Order data 

 

Article number 

SIMATIC Ident CB 2H Gate 

2 antennas, 1 read point for simple coverage 

6GT2881-1AB02-0AA0 

SIMATIC Ident CB 4H Gate 

4 antennas, 1 read point for two-sided coverage 

6GT2881-1AB04-0AA0 

SIMATIC Ident CB 4H Gate for Tire  

4 antennas, 2 read points for two-sided coverage 

6GT2881-1AB04-0AB0 

 

Table A- 2 

Order data, individual components 

 

Article number 

Controller SIMATIC S7 

CPU 1212C 

6ES7212-1AE40-0XB0 

Reader  

SIMATIC RF680R (ETSI) 

6GT2811-6AA10-0AA0 

Antennas  

SIMATIC RF650A 

6GT2812-0GB08 

Panel 

SIMATIC HMI TP900 Comfort 

6AV2124-0JC01-0AX0 

Switch 

SCALANCE XB005 

6GK5005-0BA00-1AB2 

Power supply unit 

SITOP PSU6200 

6EP3334-7SB00-3AX0 

Light barrier 

50134290 

DIN rail mounting kit 

for SIMATIC RF600 readers 

6GT2890-0AB00 

Antenna holder 3-way kit 

for SIMATIC RF600-Reader and antennas 

6GT2890-2AB10 

Ethernet plug 

Industrial Ethernet FastConnect RJ45 plug 180 2x2 (10 units) 

6GK1901-1BB10-2AB0 

 

Summary of Contents for SIMATIC Ident CB Gate







































































Reviews:

No comments