manualshive.com logo in svg

Siemens SIMATIC Ident CB Gate, Operating Instructions Manual, Page: 41 / 70

Share
Download
Siemens SIMATIC Ident CB Gate Operating Instructions Manual Download Page 41

 

SIMATIC Ident CB Gate 
Operating Instructions, 08/2022, C79000-G8976-C671-01 

41

 

Operation via the CB Gate user interface

 

8 

8.1

 

Structure of the user interface 

Configuration, operation and reading of information from the SIMATIC Ident CB Gate takes 

place via the SIMATIC HMI TP900 Comfort Panel. 

 

 

NOTICE 
Security recommendation: Authentication 

Note that the controller, the reader and the Panel are password-protected in the factory 

state. The password for the user "admin" is "CB_Gate2022!". 
To ensure that no unauthorized persons can access the CB Gate settings, we recommend 

that you leave authentication enabled, change existing passwords and create new user 

profiles. You should also read the information under the "Passwords" heading of the 

"Security recommendations (Page 7)" section. 
The authentication can only be enabled/disabled by an administrator. 
For additional information on creating/deleting user profiles, refer to the section ""User 

management" menu item (Page 58)". 

 

Summary of Contents for SIMATIC Ident CB Gate







































































Reviews:

No comments