manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 84 / 196

Share
Download
Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 84

Parameterizing the Mobile Panel 

 

5.6 Configuring operation 

 

TP1000F Mobile RO 

84

 

Operating Instructions, 08/2017, A5E39831415-AA  

5.6.4

 

Setting the double-click 

You start applications in the Control Panel and in the operating system with a double-click. A 

double-click corresponds to two brief touches. 
In the "Mouse Properties" dialog, make the following settings for operation with the touch 

screen: 

●

 

Interval between two touch contacts on the touch screen 

●

 

Interval between the two clicks of a double-click 

Requirement 

The Control Panel is open. 

Procedure  

1.

 

Open the "Mouse Properties" dialog using the "Mouse" icon. 

 

①

 

"Checkered pattern" icon 

②

 

"Test" icon 

2.

 

Double-click the "Checkered pattern" icon. 

After the double-click, the colors in the pattern are inverted. White boxes become gray. 

The timeframe for the double-click is saved. 

 

3.

 

Check the double-click: Press the "Test" icon twice in succession. If the double-click is 

recognized, the "Test" icon is displayed as follows: 

 

4.

 

Repeat steps 2 and 3 as necessary until the settings are okay. 

5.

 

Confirm your entry with "OK". 

The dialog closes. 

The double-click adjustment is completed. 

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Reviews:

No comments