manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 20 / 196

Share
Download
Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 20

Overview 

 

1.6 Accessories 

 

TP1000F Mobile RO 

20

 

Operating Instructions, 08/2017, A5E39831415-AA  

1.6.3

 

Touch pens 

The touch pens make it easier to operate the touch screen. 
The touch pen set is not included with the HMI device. The touch pen set contains 5 pens 

and is available under article number 6AV6645-7AB14-0AS0. 

1.6.4

 

Storage media 

You can use the storage media to back up Mobile Panel data and copy data to the Mobile 

Panel. Use the following storage media: 

●

 

SIMATIC HMI Memory Card 
Siemens AG has approved the use of SD memory cards in the Mobile Panel.  

●

 

USB flash drive 
The USB flash drive must be suitable for industrial applications. The storage medium is 

inserted in the port on the left of the device.  

1.6.5

 

SIRIUS safety relay 

If you are using a fail-safe Mobile Panel in a hardwired F system, you must use a safety 

relay.  
The Mobile Panels 2nd Generation have been tested with the following safety relays and 

approved: 

●

 

SIRIUS safety relay, standard, relay output 

article number 3SK1111-1AB30 

●

 

SIRIUS safety relay, standard, electronic output 

article number 3SK1112-1BB40 

●

 

SIRIUS safety relay, advanced, relay output 

article number 3SK1121-1AB40 

●

 

SIRIUS safety relay, advanced, electronic output 

article number 3SK1122-1AB40 

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Reviews:

No comments