manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 171 / 196

Share
Download
Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 171

 

Technical specifications 

 

9.7 Technical specifications 

TP1000F Mobile RO 
Operating Instructions, 08/2017, A5E39831415-AA  

171

 

Reaction times  

The table shows below the reaction times of the HMI device up to the output or interface X10 

of the connection box, dependent on the F-system. 

 

Operating mode  Stop/E-stop button evaluated 

by safety relay 

Reaction time 
Emergency stop / stop button 

 

Reaction time during error-free 

operation  

Press switch 

< 10 ms 

Unlock switch 

< 10 ms 

Reaction time with error 

Discrepancy detected (safe state) 

See Safety relay 

Critical internal error 

< 30 ms 

Discrepancy time 

See Safety relay 

Acknowledgment time in safety mode 

– 

Enabling 

 

Reaction time during error-free 

operation 

No Enabling or Panic 

< 15 ms 

Enabling 

< 40 ms 

Reaction time with error pending  Discrepancy detected (safe state) 

< 15 ms 

Critical internal error 

< 30 ms 

Discrepancy time 

500 ms 

Acknowledgment time in safety mode 

- 

 
 

 

Note 
Times 
The specified times do not include the applicable safety relay. 

 

Safety characteristics 

 

 

Note 
All values for the following information are based on the SN 29500:2005 and an ambient 

temperature of 60 °C. 

 

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Reviews:

No comments