Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 166

Page: 166 / 196

Technical specifications

9.7 Technical specifications

TP1000F Mobile RO

166

Operating Instructions, 08/2017, A5E39831415-AA

Interfaces

TP1000F Mobile RO

1 × Ethernet RJ45

10/100 Mbps

USB 2.0

Yes

Power supply, via connection box

TP1000F Mobile RO

Rated voltage

+24 V DC

Permitted voltage range

19.2 … 28.8 V (24 V ± 20%)

Transients, maximum permitted

35 V (500 ms)

Time between two transients

≥ 50

Current consumption, maximum

Approx. 830 mA

Current consumption, typical

Approx. 450 mA

Inrush current I

Approx. 0.2 A

Fuse, internal

Electronic

Bridging time after the HMI device has been disconnected from

the connection box

5 minutes

Charging time on the connection box until the bridging time is

guaranteed

2 minutes

Miscellaneous

TP1000F Mobile RO

Real time clock, buffered, can be synchronized

Yes, typical buffer period 3 weeks

Feedback, acoustic

Insulation testing, protection class and degree of protection

Insulation testing
The insulation strength is demonstrated in the type test with the following test voltages in

accordance with IEC 61131-2:

Circuits with rated voltage of U

Test voltage

< 50 V

500 V AC to other circuits / to ground

Protection class
Protection class III according to IEC 61131-2.

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Search results

Summary of Contents for SIMATIC HMI TP1000F Mobile RO

Reviews:

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 166 / 196

Search results

Summary of Contents for SIMATIC HMI TP1000F Mobile RO

Reviews: