manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 14 / 196

Share
Download
Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 14

Overview 

 

1.3 KTP Mobile connecting cable 

 

TP1000F Mobile RO 

14

 

Operating Instructions, 08/2017, A5E39831415-AA  

1.3

 

KTP Mobile connecting cable 

The connecting cable is resistant to many solvents and lubricants. The tensile and flexural 

strength of the connecting cable is geared toward the actual usage conditions.  
Functions of the connecting cable: 

●

 

Power supply of the Mobile Panel 

●

 

Ethernet connection between Mobile Panel and connection box 

●

 

Transmission of the signals for emergency stop / stop button and enabling button 

●

 

Transmission of the box ID 

 

①

 

RJ45 connector 

②

 

Plug connector, 12-pin 

③

 

Retainer, not required for KTP400F Mobile. 

④

 

Label with order number, length specification and product version 

⑤

 

Seal 

⑥

 

Terminal compartment cover 

⑦

 

Plug connector for the connection box 

The KTP Mobile connecting cable is available in the following lengths: 

 

Product name and length 

Article number 

KTP Mobile 2 m connecting cable  6AV2181-5AF02-0AX0 
KTP Mobile 5 m connecting cable  6AV2181-5AF05-0AX0 
KTP Mobile 8 m connecting cable  6AV2181-5AF08-0AX0 
KTP Mobile 10 m connecting cable  6AV2181-5AF10-0AX0 
KTP Mobile 15 m connecting cable  6AV2181-5AF15-0AX0 
KTP Mobile 20 m connecting cable  6AV2181-5AF20-0AX0 
KTP Mobile 25m connecting cable  6AV2181-5AF25-0AX0 

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Reviews:

No comments