manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 109 / 196

Share
Download
Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 109

 

Parameterizing the Mobile Panel 

 

5.10 Server time 

TP1000F Mobile RO 
Operating Instructions, 08/2017, A5E39831415-AA  

109

 

5.10

 

Server time 

To obtain the time of the HMI device from a time server, you can specify up to four different 

time servers. The time is synchronized using the "Network Time Protocol". The 

synchronization cycle applies to all configured time servers. 

Requirement  

●

 

The HMI device and time server are located in the same network. 

●

 

The Control Panel is open. 

Procedure 

1.

 

Open the "PROFINET" dialog using the "PROFINET" icon. 

2.

 

Change to the "NTP" tab. 

 

①

 

Text box for time servers 1 to 4 

②

 

Button for configuring the time servers 

3.

 

If you want to use the time of a time server, activate "Automatically synchronize with …". 

4.

 

Under "Update rate", enter the time interval in seconds after which the HMI device is to 

synchronize the time. 

Permitted value range: 1 ... 60 000 000 seconds. 

5.

 

Press the "Configure" button. 

The following dialog is displayed: 

 

If you do not enter a time, the message "Second field wrong data type." will appear. Enter 

a time. 

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Reviews:

No comments