Siemens SIMATIC ET 200SP IM 155-6 PN/2 HF, Manual, Page: 24 / 57

Share

Page: 24 / 57

Siemens SIMATIC ET 200SP IM 155-6 PN/2 HF Manual Download Page 24

Product overview

2.2 Functions

Interface module IM 155-6 PN/2 HF (6ES7155-6AU01-0CN0)
Manual, 10/2018, A5E03915895-AH

23

2.2.6

Media redundancy (MRP)

Media redundancy (MRP)

Function for safeguarding communication and plant availability. A ring topology ensures that

an alternative communication path is made available if a transmission route fails.
You can find more information on this topic in the STEP 7 online help and

●

As of STEP 7 V12, in the function manual PROFINET with STEP 7

http://support.automation.siemens.com/WW/view/en/49948856

●

As of STEP 7 V5.5, in the system manual PROFINET System Description

http://support.automation.siemens.com/WW/view/en/19292127

2.2.7

Shared device

Shared device

IO device that makes its data available to up to four IO controllers.
The interface module supports shared device at submodule level.
If there is no validity check of the shared device projects by the Engineering System, note

the following:

●

Make sure the configurations are consistent. Assign each module or submodule to only

one IO controller. Multiple assignment will result in an error as the module or submodule

will only be available in the first controller.

●

If you reconfigure the shared device configurations without the validity check mentioned

above, you must commission ET 200SP again. This means you must download the

projects of all involved IO controllers to the respective CPU again after reconfiguration. If

necessary, perform a POWER OFF/POWER ON of the interface module.

You can find more information on this topic in the STEP 7 online help and

●

As of STEP 7 V12, in the function manual PROFINET with STEP 7

http://support.automation.siemens.com/WW/view/en/49948856

●

As of STEP 7 V5.5, in the system manual PROFINET System Description

http://support.automation.siemens.com/WW/view/en/19292127

Note
In the case of a shared device application, make sure that all controllers work with the same

send clock. If the controller does not have the same send clock, this results in

communication relationships not being set up.
If you set up all controllers in one project, the same send clock is ensured. Set the same

send clock for engineering in separate projects.

«
...
22
23
24
25
26
...
»

Summary of Contents for SIMATIC ET 200SP IM 155-6 PN/2 HF


























































Reviews:

No comments