Siemens SIMATIC ET 200SP CM 1xDALI Manual Download Page 117

Page: 117 / 126

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0)

116

Manual, 06/2019, A5E46959434-AA

Appendix B Approvals

This chapter lists the approval for ET 200SP CM 1xDALI specifically.
Detailed references to the other approvals of CM 1xDALI are listed in the document

200SP Distributed I/O system.

Note
Information of the ET 200SP CM 1xDALI
The currently valid markings and approvals are printed on the components of the ET 200SP

CM 1xDALI.

DALI-2

IECEx

The CM 1xDALI meets the requirements of the DALI-2 standards.

The CM 1xDALI meet

the requirements of explosion protection according to

IECEx. IECEx classification: Ex nA IIC T4 Gc
IECEx certificate: IECEx DEK 19.0024X
The CP meets the requirements of the following standards:

●

IEC 60079-0
Hazardous areas - Part 0: Equipment - General requirements

●

EN 60079-15
Explosive atmospheres - Part 15: Equipment protection by type of protection 'n'

ATEX

The CP meets the requirements of the EC directive 2014/34/EU "Equipment and Protective

Devices for Use in Potentially Explosive Atmospheres".
Applied standards:

●

EN 60079-0
Hazardous areas - Part 0: Equipment - General requirements

●

EN 60079-15
Explosive atmospheres - Part 15: Equipment protection by type of protection 'n'

The current versions of the standards can be seen in the EC Declaration of Conformity, see

above.

Summary of Contents for SIMATIC ET 200SP CM 1xDALI































































































































Search results

Summary of Contents for SIMATIC ET 200SP CM 1xDALI

Reviews:

Siemens SIMATIC ET 200SP CM 1xDALI, Manual, Page: 117 / 126

Search results

Summary of Contents for SIMATIC ET 200SP CM 1xDALI

Reviews: