Siemens Simatic ET 200pro FC Operating Instructions Manual Download Page 59

Page: 59 / 196

Installation

4.9 Mounting a fail-safe frequency converter

ET 200pro FC
Operating Instructions, 07/2016, A5E01100763B AC

4.9

Mounting a fail-safe frequency converter

Fail-safe applications are configured basically the same as standard applications but with the

following differences:

●

Mounted to the left of the frequency converter must be a module through which the safety

functions of the frequency converter can be actuated, for example:
–

an F-RSM repair switch module

–

an F-Switch

●

Only the following modules are allowed to be connected between the F-RSM or F-Switch

and the fail-safe frequency converter:
–

400 V shutdown module

–

all direct or reversing starters

–

the standard frequency converter

–

the fail-safe frequency converter

Procedure:

Mount one after the other:
1.

Rack

Interface module

Bus module for F-RSM or F-Switch

Bus module for frequency converter

Terminating module

Connection module for the interface module

F-RSM or F-Switch

Frequency converter

Summary of Contents for Simatic ET 200pro FC





































































































































































































Search results

Summary of Contents for Simatic ET 200pro FC

Reviews:

Brands by name

Popular brands

Siemens Simatic ET 200pro FC, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET 200pro FC

Reviews:

Brands by name

Popular brands