Siemens Simatic ET 200pro FC Operating Instructions Manual Download Page 17

Page: 17 / 196

Fundamental safety instructions

1.2 Safety instructions for electromagnetic fields (EMF)

ET 200pro FC
Operating Instructions, 07/2016, A5E01100763B AC

WARNING

Danger to life or malfunctions of the machine as a result of incorrect or changed

parameterization
As a result of incorrect or changed parameterization, machines can malfunction, which in

turn can lead to injuries or death.

•

Protect the parameterization (parameter assignments) against unauthorized access.

•

Respond to possible malfunctions by applying suitable measures (e.g. EMERGENCY

STOP or EMERGENCY OFF).

1.2

Safety instructions for electromagnetic fields (EMF)

WARNING

Danger to life from electromagnetic fields
Electromagnetic fields (EMF) are generated by the operation of electrical power equipment

such as transformers, converters or motors.
People with pacemakers or implants are at a special risk in the immediate vicinity of these

devices/systems.

•

Ensure that the persons involved are the necessary distance away (minimum 2 m).

Summary of Contents for Simatic ET 200pro FC





































































































































































































Search results

Summary of Contents for Simatic ET 200pro FC

Reviews:

Brands by name

Popular brands

Siemens Simatic ET 200pro FC, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET 200pro FC

Reviews:

Brands by name

Popular brands