Siemens SIMATIC CPU 1515SP PC2 F User Manual Download Page 8

Page: 8 / 136

Introduction

1.1 Documentation on CPU 1515SP PC2

CPU 1515SP PC2 (F/T/TF)
Operating Instructions, 09/2018, A5E42603425-AA

Conventions

STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the

configuration and programming software "STEP 7 (TIA Portal)".
"CPU1515SP PC2 T" means that the respective section applies only to the

"CPU 1515SP PC2 T".
"CPU1515SP PC2 F" means that the respective section applies only to the

"CPU 1515SP PC2 F".
"CPU1515SP PC2 TF" means that the respective section applies only to the

"CPU 1515SP PC2 TF".
"CPU 1515SP PC2" also includes "CPU1 515SP PC2 F", "CPU 1515SP PC2 T" and

"CPU 1515SP PC2 TF".
Please also observe notes marked as follows:

Note
A note contains important information on the product described in the documentation, on the

handling of the product or on the section of the documentation to which particular attention

should be paid.

Scope of validity of the documentation

This documentation is valid for the following products:

ET 200SP Open Controller

Article number

Standard CPU

•

CPU 1515SP PC2 basic device

6ES7677-2DB40-0AA0

•

CPU 1515SP PC2

6ES7677-2DB42-0GB0

•

CPU 1515SP PC2 + HMI 128PT

6ES7677-2DB42-0GK0

•

CPU 1515SP PC2 + HMI 512PT

6ES7677-2DB42-0GL0

•

CPU 1515SP PC2 + HMI 2048PT

6ES7677-2DB42-0GM0

Fail-safe CPUs

•

CPU 1515SP PC2 F

6ES7677-2SB42-0GB0

•

CPU 1515SP PC2 F + HMI 128PT

6ES7677-2SB42-0GK0

•

CPU 1515SP PC2 F + HMI 512PT

6ES7677-2SB42-0GL0

•

CPU 1515SP PC2 F + HMI 2048PT

6ES7677-2SB42-0GM0

Technology CPUs

•

CPU 1515SP PC2 T

6ES7677-2VB42-0GB0

Fail-safe technology CPUs

•

CPU 1515SP PC2 TF

6ES7677-2WB42-0GB0

Summary of Contents for SIMATIC CPU 1515SP PC2 F









































































































































Search results

Summary of Contents for SIMATIC CPU 1515SP PC2 F

Reviews:

Brands by name

Popular brands

Siemens SIMATIC CPU 1515SP PC2 F, User Manual

Search results

Summary of Contents for SIMATIC CPU 1515SP PC2 F

Reviews:

Brands by name

Popular brands