Siemens SIMATIC CN 4100 Equipment Manual Download Page 63

Page: 63 / 76

10.2

Technical specifications of components

10.2.1

Technical specifications - CPU module

Technical specifications TED

Article number

6DL4178-0BH01-0XX0

General information

Product type designation

CPU modules 1 slot

HW functional status

FS02

Firmware version

V1.0

Engineering with

• PCS 7 configurable/integrated from version

V9.0 SP3

Supply voltage

Rated value (DC)

24 V

permissible range, lower limit (DC)

20.4 V

permissible range, upper limit (DC)

28.8 V

Input current

Current consumption, max.

400 mA; without USB power supply

Power loss

Power loss, typ.

10 W

Memory

Type of memory

Flash

Work memory

• integrated

2 Gbyte; ECC

• expandable

Backup

• present

Yes; Entire project maintenance-free in the integral
EEPROM

• Number, max.

16 000

Hardware configuration

Slots

• required slots

Interfaces

Number of industrial Ethernet interfaces

Protocols

Supports protocol for PROFINET IO

EtherNet/IP

Modbus TCP

Yes

S7 protocol

Yes

OPC UA

Yes

OPC UA

Technical specifications

10.2 Technical specifications of components

CN 4100 Communication System
Equipment Manual, 10/2021, A5E50871363-AA

Summary of Contents for SIMATIC CN 4100













































































Search results

Summary of Contents for SIMATIC CN 4100

Reviews:

Siemens SIMATIC CN 4100, Equipment Manual, Page: 63 / 76

Search results

Summary of Contents for SIMATIC CN 4100

Reviews: