Siemens SIMATIC CN 4100 Equipment Manual Download Page 38

Page: 38 / 76

①

Crimping TWIN end sleeves at the correct angle

②

Cross-section of the terminal compartment
• a: 1.8 mm
• b: 2.4 mm

③

Spring release

Mechanical and climatic environmental conditions (Page 59)

6.3

Overview of rack wiring

There are terminals for the supply voltage on the rack.

Supply voltage (Page 43)

Power supply

Note the technical specifications and the information on the supply voltage in the section "Notes
on operation (Page 35)".

Terminals for power supply

Observe the wiring rules for the SIMATIC CN 4100 communication system.

Notes on wiring (Page 36)

Connecting or disconnecting the power supply

Connecting the supply voltage to the rack (Page 44)

Disconnecting the supply voltage from the rack (Page 44)

Connecting
6.3 Overview of rack wiring

CN 4100 Communication System

Equipment Manual, 10/2021, A5E50871363-AA

Summary of Contents for SIMATIC CN 4100













































































Search results

Summary of Contents for SIMATIC CN 4100

Reviews:

Siemens SIMATIC CN 4100, Equipment Manual, Page: 38 / 76

Search results

Summary of Contents for SIMATIC CN 4100

Reviews: