manualshive.com logo in svg

Siemens SICAM Q100 7KG95 Series, Manual, Page: 441 / 448

Share
Download
Siemens SICAM Q100 7KG95 Series Manual Download Page 441

 

 

441

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

Glossary

A

AC

A

lternating 

C

urrent

ADC

A

nalog-

d

igital

 C

onverter

ARP

A

ddress 

R

esolution 

P

rotocol: Network protocol

ASDU

A

pplication 

S

ervice 

D

ata 

U

nit

B

Big-Endian format

The most significant byte is stored first, that is at the memory location with 

the lowest address.

Boot Application

Starting a device with the firmware required for the microcontroller

Broadcast message

Message in the network where data packets are transmitted to all devices 

on the network from one point

C

CDC

C

ommon 

D

ata 

C

lass (IEC 61850)

Client

Device in the communication network that sends data requests or com-

mands to the server devices and receives responses from them

CRC error

C

yclic 

R

edundancy 

C

heck: The cyclic redundancy check is a method of de-

termining a test value for data (e.g. for data transmission in computer net-
works) with the purpose to detect errors during the transmission or 
duplication of data.

D

DC

D

irect 

C

urrent

DHCP

D

ynamic 

H

ost 

C

onfiguration 

P

rotocol enables the network configuration to 

be assigned to the devices by a DHCP server

DSP

D

igital 

S

ignal 

P

rocessor

DST

D

aylight 

S

aving 

T

ime

E

Ethernet

Cable-based data network technology for local data networks

F

FW

F

irm

w

are: Program code for execution in a microcontroller

G

Gateway

Enables networks based on different protocols to communicate with each 

other

MAN_SICAM_Q100_US.book  Page 441  Wednesday, June 5, 2019  9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Reviews:

No comments