Siemens SICAM Q100 7KG95 Series, Manual, Page: 334 / 448

Share

Page: 334 / 448

Siemens SICAM Q100 7KG95 Series Manual Download Page 334

9 Operation at Use of a PC

9.7 Example of a Parameterization and Measured Value Evaluation

334

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

✧

Enable the active parameter set in the device as described in

Activating the Set of Parameters

.

9.7.4

Performing the Measurement

✧

Switch on the rated voltages and rated currents at the measuring inputs E and F of SICAM Q100
observing the safety notes given in chapter 7.7.

✧

Read the measured values from the

Value view and Evaluation

tab by calling the

Operational

parameters

,

Harmonics

,

AC power and energy

,

Binary outputs

and

Limits

menu items according to

chapter 9.4 in the navigation window.
The user interface displays the status of binary output G1/2 which corresponds to the parameterized
indication Vab_>11kV.

If the parameterized limit of the voltage Vab is exceeded, a corresponding limit violation indication is
displayed in the table.

✧

Display the power quality events and the memory utilization on the

Value view and Evaluation

tab.

NOTE

After changing the network settings and subsequent parameter activation the device will reset.

NOTE

Measured values and indications are refreshed after 5 s on the

Value view and Evaluation

tab.

MAN_SICAM_Q100_US.book Page 334 Wednesday, June 5, 2019 9:31 AM

«
...
332
333
334
335
336
...
»

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Reviews:

No comments