Siemens SICAM Q100 7KG95 Series, Manual, Page: 30 / 448

Share

Page: 30 / 448

Siemens SICAM Q100 7KG95 Series Manual Download Page 30

4 Measured Quantities and Recording

4.1 Power Quality Measuring System and Recording System

30

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

4.1

Power Quality Measuring System and Recording System

4.1.1

Measuring System

SICAM Q100 devices measure the power quality according to IEC 61000-4-30 in 1-phase or multi-phase
distribution systems.

The basic measuring interval for determining the values for mains voltage, harmonics of mains voltage, and
mains voltage unbalance is 10 cycles for 50-Hz distribution systems or 12 cycles for 60-Hz distribution systems.

An overview of the measured quantities demanded in according to IEC 61000-4-30, their measurement
uncertainty and measurement ranges is represented in the chapter 4.3.1.

4.1.2

Flicker

The flicker measurement is performed according to IEC 61000-4-15.

The short-term flicker value Pst and long-term flicker value Plt are determined for phase-to-ground voltages
and delta voltages. The flicker measurement is performed on all 3 voltage channels.

Flickers appear with a frequency from 0.005 to 35 Hz. The instantaneous flicker value is displayed in
perceptibility units P.

SICAM Q100 measures the following flicker types:

•

Short-term flicker value Pst, determined over 10 min (short-term flicker), fixed

•

Long-term flicker value Plt, over 2 h (12 Pst values), fixed

•

Perceptibility Pinst

MAN_SICAM_Q100_US.book Page 30 Wednesday, June 5, 2019 9:31 AM

«
...
28
29
30
31
32
...
»

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Reviews:

No comments