Siemens SICAM Q100 7KG95 Series Manual Download Page 173

Page: 173 / 448

9 Operation at Use of a PC

9.3 Configuration of the Device

173

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

9.3.3.1.4

LEDs

Default Settings and Setting Options of the LEDs

Parameterization of the LEDs

To change the outputs of the LEDs H1, H2, and ERROR, proceed as follows:

✧

In the navigation window, select the

Operational

parameters

menu, then the

Process connections

submenu and click

LEDs

Figure 9-31

Configure Tab, LEDs Input/Output Window

Table 9-5LED Settings

LED

Default Setting

Setting Options

RUN

Device ready

Not settable

-none-

Acc. to list box

(see chapter 16)

ERROR

-none-

Errors are signaled as parameterized (only
error indications can be parameterized).

Acc. to list box

(see chapter 16)

Indication inverted

no
yes

MAN_SICAM_Q100_US.book Page 173 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 173 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: