manualshive.com logo in svg

Siemens SICAM Q100 7KG95 Series, Manual, Page: 128 / 448

Share
Download
Siemens SICAM Q100 7KG95 Series Manual Download Page 128

8 Connection Principle

8.2 Communication Interfaces

128

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

8.2

Communication Interfaces

8.2.1

Ethernet Interface

The Ethernet interface 

Z

 is located on the top side of the SICAM Q100. Data are exchanged via the 

RJ45 Ethernet socket, see also detailed information in System Manual SICAM Q100 7KG95xx, order number 
E50417-C1040-C482, chapter 2.

Figure 8-2

Ethernet Interface Z (Detail of the Top Side) 

If you use a Y cable and the internal Ethernet switch of the device, SICAM Q100 can be connected with a SI-
CAM I/O Unit. This device combination can be connected with the process control via the second connector of 
the Y cable and an external Ethernet switch. For typical circuit diagrams, refer to the System Manual 
SICAM Q100 7KG95xx, order no. E50417-C1000-C522, chapter 2.

8.2.2

RS485 Interface

The RS485 interface 

J 

(D-Sub) is located on the terminal side; see also detailed information in the System Man-

ual SICAM Q100 7KG95xx, order no. E50417-C1000-C522, chapter 2.

Figure 8-3

RS485 Interface J (Detail of the Terminal Side)

Ethernet socket

(RJ45)

NOTE

If you do not connect a cable to the RJ45 socket, Siemens recommends covering the socket with a cap or dum-
my plug (not included in the delivery) to prevent the contacts from becoming dirty.

RS485 connector
(D-sub)

NOTE

If you do not connect a cable to the RS485 connector, Siemens recommends covering it with a cap (not includ-
ed in the delivery) to prevent the contacts from becoming dirty.

MAN_SICAM_Q100_US.book  Page 128  Wednesday, June 5, 2019  9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Reviews:

No comments