Siemens SICAM P37 Manual Download Page 14 | Manualshive

Page: 14 / 56

Siemens SICAM P37 Manual Download Page 14

Functions
3.1 Measurement

SICAM P37, 3-phase Harmonic Power Meter, User Manual

E50417-H8940-C563-

4

, Release Date

06.2018

14

3.1

Measurement

This meter is provided with various measuring functions. Power grid parameters and index measurable are as
follows:

• Voltage of each phase and mean voltage

• Voltage of each line and mean voltage

• Current of each phase, average current and neutral current

• Total and separate active power, reactive power and apparent power of each phase

• Phase angle of voltage and current of each phase

• Total and separate power factor of each phase

• Power grid frequency and measuring range 45 Hz to 65 Hz

• Effective value and ratio of 2

nd

to 50

th

harmonic voltage and harmonic current of each phase

- Harmonic voltage ratio:

where, U

h

- No. h harmonic voltage (RMS); U

1

- fundamental voltage (RMS).

- Harmonic current ratio:

where, I

h

- No. h harmonic current (RMS); I

1

- fundamental current (RMS).

• Total harmonic voltage distortion and total harmonic current distortion of each phase
- Total harmonic voltage distortion:

- Total harmonic current distortion:

• Voltage wave crest factor (CF) of each phase, indicating peak of distorted waveform

«
...
12
13
14
15
16
...
»

Summary of Contents for SICAM P37

























































Reviews:

No comments