manualshive.com logo in svg

Siemens SICAM P 7KG7750, Manual, Page: 71 / 142

Share
Download
Siemens SICAM P 7KG7750 Manual Download Page 71

4

4.4 Basic Settings

71

Power Meter SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

4.4.8

Further Settings

Calculation mode

•

Standard

•

DIN

•

Fourier

The calculation mode for some measured quantities can be changed here. For further informa-
tion, see the chapter 3.1.

Current direction

•

+

Default setting for correct connection according to standard and back panel marking

•

-

Current direction is negated (change the current direction to avoid changing the connec-

tors)

Direction of power

•

+

positive energy flow direction = energy demand

negative energy flow direction = energy supply

•

- 

positive energy flow direction = energy supply

negative energy flow direction = energy demand

Zero point

The zero point suppression can be changed here. 

Can be selected from 0.0 % to 10.0 % of the upper limit of the measurement range (default set-
ting: 1 %)

*calc. mode: standard
*current direction: +
*direction of power:+
*zero point:  0.3000%
Uen:

calculation

AO settings
<ok
<cancel

Note

Due to its high precision, SICAM P can measure voltages and currents even without measuring 
values connected to the device. If you do not want this behaviour in your application, you can 
suppress measuring below a certain threshold.

Summary of Contents for SICAM P 7KG7750















































































































































Reviews:

No comments