manualshive.com logo in svg

Siemens SICAM P 7KG7750, Manual, Page: 69 / 142

Share
Download
Siemens SICAM P 7KG7750 Manual Download Page 69

4

4.4 Basic Settings

69

Power Meter SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

4.4.5

Changing the Password

4.4.5.1

Password of Code 1

off

:

No function

on

:

Active if code 2 is active

Secured functions:

Parameterization the screens

Reset

Language / Designation

4.4.5.2

Password of Code 2

off

:

No function (code 1 is also deactivated )

on

:

Code activated

Secured functions:

Basic settings

Notes

•

A password always consists of a 6-digit number.

•

If you have forgotten the password, the device can also be activated by using the master 
password. Please contact our hotline for the master password.

•

Password 1 is only active if password 2 is also activated.

•

If both password 1 and password 2 are activated, password 2 can be used to access all pro-
tected functions of password 1.

•

If an identical password is chosen for password 1 and password 2, all functions of password 
1 and password 2 can be activated by means of a single password.

•

In Level 1, a lock displayed on the status bar indicates whether the status of the device is 
password protected (lock closed) or unprotected (lock open).

•

After a password has been programmed, a time of 1 minute elapses before it is activated in 
level 1 (the activation can be detected when the lock closes on the status bar).

*code1: 000000
*       off
*code2: 000000
*       off

<ok
<cancel

Summary of Contents for SICAM P 7KG7750















































































































































Reviews:

No comments