manualshive.com logo in svg

Siemens SICAM P 7KG7750, Manual, Page: 55 / 142

Share
Download
Siemens SICAM P 7KG7750 Manual Download Page 55

4

4.1 Operating Notes

55

Power Meter SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

4.1.3

Notes on Parameterization

•

The measured quantities offered for selection in the screens depend on the connection type 
selected.

•

The numbers entered are checked for plausibility and the note: "ERR" is displayed if required. 
The input value is then set to the maximum value. 

•

If the power supply voltage is switched off during programming, the message illustrated 
below appears when the device is restarted. Therefore, the power supply voltage should only 
be switched off in level 1 (measuring screens).

Select 

No

 via the 

buttons to 

retain the settings as they existed prior to the 
loss of power supply voltage.

Choose 

Yes

 by pressing the ENTER button 

to restore the default settings. 

Attention!

Parameter incorrect

reset?

No          Yes

(arrow)      (Enter)

Note

This means, that you should always leave the parameter screens completely (OK or Cancel) until 
the measurement screens are displayed again. This ensures that all parameters will be accepted 
by the device.

Note

Please check the parameters and the adjustment data afterwards, to ensure the correct function 
of the SICAM P.

If you have adjusted the device manually (refer to chapter 6), the adjustment data will not be 
overwritten by default settings.

Summary of Contents for SICAM P 7KG7750















































































































































Reviews:

No comments