manualshive.com logo in svg

Siemens SICAM P 7KG7750, Manual, Page: 25 / 142

Share
Download
Siemens SICAM P 7KG7750 Manual Download Page 25

1

1.6 Interface and Terminals

25

Power Meter SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

1.6.3

Assignment of the Interface

Table 1-3 

Terminal assignment of RS485 interface

The housing of the RS485 interface is connected to the protective ground. We recommend using 
standard connecting cables. The bus termination is accomplished via the connecting cable. 

The isolated supply voltage of the interface is available at the D-Sub female connector, thus 
allowing the data signal terminating resistors to be connected to the connecting cable.

Fig. 1-8 

Termination of the RS485 interface (external)

Pin No.

RS485 Interface

Modbus / IEC 60870-5-103

Profibus DP

1

Shield

Shield

2

3

A

B(RxD/TxD-P)

4

5

GND

EXT

GND

EXT

6

+5  V

EXT

+5 V

EXT

7

RTS

CTRL-A

8

B

A(RxD/TxD-N)

9

+5 V

390 Ω

220 Ω

390 Ω

B

A

Note

All computing devices connected to the RS485 interface port shall be connected to a SELV (Sep-
arated Extra Low Voltage) circuit and must comply with the following standard: IEC/EN 60950.

Summary of Contents for SICAM P 7KG7750















































































































































Reviews:

No comments