manualshive.com logo in svg

Siemens SICAM 7KG85X, Manual, Page: 75 / 281

Share
Download
Siemens SICAM 7KG85X Manual Download Page 75

Serial Communication

Modbus RTU Slave

Function Description

The serial communication using Modbus RTU (slave) with the device is executed via the RS485 interface.

Configuration via Web Pages

Configuration of the Serial Communication with Modbus RTU (Slave) via RS485 Interface

Precondition: The Modbus RTU protocol must have been activated for the RS485 interface.
To change the Modbus RTU (slave) settings in the Configuration tab, proceed as follows:

•

In the navigation window, click Communication serial and select Modbus RTU as the Bus protocol.

[sc_config_Modbus_RTU, 1, en_US]

Figure 2-35

Configuration Tab, Modbus RTU (Slave)

•

Configure the respective parameters according to the following table.

Table 2-21

Settings for Communication Serial, Modbus RTU (Slave)

Parameter

Default Setting

Setting Range

Bus protocol

Modbus RTU

None
Modbus RTU 

(slave)

IEC 60870-5-103

Device address

1

1 to 247

Baud rate

19 200 bit/s

1200 bit/s, 2400 bit/s,
4800 bit/s, 9600 bit/s,
19 200 bit/s, 38 400 bit/s,
57 600 bit/s, 115 200 bit/s

2.7

2.7.1

2.7.1.1

2.7.1.2

Basic Functions
2.7 Serial Communication

74

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Reviews:

No comments