Siemens SICAM 7KG85X Manual Download Page 38

Page: 38 / 281

Configuration via Display

Submenu Device and Language

In the main menu, select Settings → Language/Regional. The displayed number is 80.2.

[dw_submenu_language_regional, 1, en_US]

Figure 2-6

Configuration Language/Regional

The following interface displays are available:

[dw_display_language_regional, 1, en_US]

Figure 2-7

Language/Regional

[dw_display_language, 1, en_US]

Figure 2-8

Language

Password Management

To set up passwords in the Configuration tab, click Device and language in the navigation window first (see

Figure 2-3

2.2.1.2

2.2.2

Basic Functions

2.2 Device and Language

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Search results

Summary of Contents for SICAM 7KG85X

Reviews:

Siemens SICAM 7KG85X, Manual, Page: 38 / 281

Search results

Summary of Contents for SICAM 7KG85X

Reviews: