Siemens SICAM 7KG85X Manual Download Page 267

Page: 267 / 281

Ethernet Communication

Communication Ethernet

Table 13-8

Settings for Communication Ethernet

Parameter

Default Setting

Setting Range

Communication Ethernet
IP address

192.168.0.55

Any
0.0.0.0 = DHCP

Subnet mask

255.255.255.0

Any

Default gateway

192.168.0.1

Any

Ethernet switch on

No
Yes

Enable SNMP

No
Yes

Bus protocol

Modbus TCP

-None-
Modbus TCP
IEC 61850

Protocol Modbus TCP

Table 13-9

Settings for Modbus TCP

Parameter

Default Setting

Setting Range

Standard port number

502

502
Not settable

Access rights

Full

Full
Read only

User-defined port 1

No
Yes

Port number

503

503 to 65 535

Access rights

Read only

Full
Read only

Port number

504

503 to 65 535

Access rights

Read only

Full
Read only

Keep alive time

10 s

0 s = switch off
1 s to 65 535 s

Communication supervision
time

600 (* 100 ms)

0 s = none
100 ms to 6 553 400 ms

NOTE

The 2 port numbers must be different from each other.

13.2.4

13.2.4.1

13.2.4.2

After the parameter changes have been enabled, the device will restart.

This parameter is available only if User-defined port 1 is set to yes.

Operational Indications and Operating Parameters
13.2 Basic Functions

266

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Search results

Summary of Contents for SICAM 7KG85X

Reviews:

Siemens SICAM 7KG85X, Manual, Page: 267 / 281

Search results

Summary of Contents for SICAM 7KG85X

Reviews: