Siemens SICAM 7KG85X Manual Download Page 220

Page: 220 / 281

[sc_changing_the_compatibility_setting, 1, en_US]

Figure 9-24

Changing the Compatibility Setting

•

In the Compatibility View Settings dialog, click the Display all websites in Compatibility View.

•

Enter the IP Address of SICAM P850/P855 device in the Add this website box, click Add.

•

Click Close.

Changing the Security Setting (only for Microsoft Internet Explorer)

NOTE

With Microsoft Internet Explorer, version 10.0 or higher, the operation is mandatory if multiple file down-
load is required in chapter

7.3.4 Multiple File Download via Internet Explorer

Changing Security Settings

In the Internet Explorer 10.0 or higher, the following operation is mandatory:

•

Select Tools → Internet Options → Security.

•

Click Custom level.
The Security Settings dialog opens.

9.11.2.5

Commissioning and First Steps

9.11 Operation via PC

SICAM, SICAM P850/P855 7KG85X, Manual

219

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Search results

Summary of Contents for SICAM 7KG85X

Reviews:

Siemens SICAM 7KG85X, Manual, Page: 220 / 281

Search results

Summary of Contents for SICAM 7KG85X

Reviews: