manualshive.com logo in svg

Siemens SICAM 7KG85X, Manual, Page: 197 / 281

Share
Download
Siemens SICAM 7KG85X Manual Download Page 197

Electrical Connection

[le_P85x_electrical connection, 1, --_--]

Figure 9-4

Electrical Connection

(1)

Terminal block H for power supply

(2)

Terminal block F for voltage measurement

(3)

Terminal block E for current measurement

(4)

Terminal block G for binary output

i

i

NOTE

Be aware of the safety instruction in chapter 

Safety Notes, Page 188

.

Power Supply

Connect the cables of the supply voltage on the terminal side of the device at terminal block H as follows:

Supply from the Alternating Voltage System

Terminal N/-: Neutral phase of the supply voltage
Terminal L/+: Phase of the supply voltage
Terminal Earthing: Protective grounding terminal

9.5

Commissioning and First Steps
9.5 Electrical Connection

196

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Reviews:

No comments