Siemens SICAM 7KG85X Manual Download Page 107

Page: 107 / 281

To download the load profile, proceed as follows:

•

Click Download load profile.
The File Download dialog opens. You can save the CSV file. For more information, refer to

7.3.3 Single

File Download

NOTE

The file extension must be .csv.

Configuration via Display

Submenu Load Profile

NOTE

If you select the Load profile parameter, the following message is displayed first:

Changing these parameters resets the load profile!

To confirm, press the softkey F4 (Ok).

[dw_submenu_load_profile_Q100, 1, en_US]

Figure 5-5

Submenu Load Profile

Table 5-3

Settings for the Load Profile

Parameter

Default Setting

Setting Range

Subperiod time

15 min

1 min to 6 min in 1-min steps,
10 min, 12 min, 15 min, 20 min, 30 min,
60 min

No. of subperiods

1 to 5

5.1.3

Energy Management
5.1 Load Profile

106

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Search results

Summary of Contents for SICAM 7KG85X

Reviews:

Siemens SICAM 7KG85X, Manual, Page: 107 / 281

Search results

Summary of Contents for SICAM 7KG85X

Reviews: