Siemens SENTRON PAC2200CLP Product Manual Download Page 91

Page: 91 / 130

Technical specifications

8.2 Labeling

PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02

8.2

Labeling

Labels on the housing of the PAC2200CLP

①

CE mark

②

MID mark with the year it was affixed

③

Number of the notified body

④

Electrical installation and maintenance by qualified personnel only

⑤

Protective insulation - device of class II

⑥

General warning symbol

⑦

Risk of electric shock

⑧

The device must not be disposed of with general domestic waste.

⑨

2D code (serial number of the device)

⑩

Hardware and firmware version

⑪

Registration number

⑫

Article number

⑬

Overvoltage category CAT III for current and voltage inputs

⑭

Frequency

⑮

Network type (1P2W)

⑯

Network type (3P4W)

⑰

Bidirectional counter

⑱

Serial number of the device
LQN/xxzzzzzzzzzz xx= year of manufacture

⑲

MAC address

Summary of Contents for SENTRON PAC2200CLP



































































































































Search results

Summary of Contents for SENTRON PAC2200CLP

Reviews:

Siemens SENTRON PAC2200CLP, Product Manual, Page: 91 / 130

Search results

Summary of Contents for SENTRON PAC2200CLP

Reviews: