Siemens SENTRON PAC2200 Product Manual Download Page 93

Page: 93 / 130

Technical specifications

8.1 Technical specifications

PAC2200
Equipment Manual, 12/2019, L1V30415167B-03

Electromagnetic environment in accordance with MID directive (2014/32/EU)

●

Class E2

Mechanical environment in accordance with MID directive (2014/32/EU)

●

Class M1

Relative humidity in relation to ambient temperature
The maximum relative humidity is 80 % at temperatures up to 31 °C, decreasing linearly

down to 50 % relative humidity at 40 °C.

Approvals

The PAC2200 complies with the requirements of the European Directives.

●

CE conformity

Applied directives and standards can be found in the EU Declaration of Conformity

(

https://support.industry.siemens.com/cs/products/7km2200-2ea30-1ca1/pmd-sentron-

pac2200-din-rail?pid=760583&dtp=Certificate&mlfb=7KM2200-2EA30-

1CA1&mfn=ps&lc=en-WW

●

Approvals for Australia and New Zealand

RCM (Regulatory Compliance Mark)

●

Approval for the Eurasian Economic Union

Summary of Contents for SENTRON PAC2200



































































































































Search results

Summary of Contents for SENTRON PAC2200

Reviews:

Siemens SENTRON PAC2200, Product Manual, Page: 93 / 130

Search results

Summary of Contents for SENTRON PAC2200

Reviews: