Siemens SENTRON PAC2200 Product Manual Download Page 90

Page: 90 / 130

Technical specifications

8.1 Technical specifications

PAC2200

Equipment Manual, 12/2019, L1V30415167B-03

Connection elements

The specified conductor cross sections describe the capacity of the connection terminals.

When selecting the conduction cross sections, always pay attention to the possible current

load and ensure adequate cable protection.

Current, power supply

5 A device

65 A device

Conductor cross-section for copper cable (Cu)

Rigid

0.2 ... 6.0 mm

[AWG 24...10]

0.75 ... 35 mm²

[AWG 19 ... 2]

Flexible

0.2 ... 4.0 mm²

[AWG 24...12]

1 ... 35mm²

[AWG 18 ... 2]

Flexible with end sleeve, without plastic

sleeve

0.2 ... 4.0 mm²

[AWG 24...12]

0.75 ... 25 mm²

[AWG 19 ... 4]

Flexible with end sleeve and plastic

sleeve

0.25 ... 4.0 mm²

[AWG 24...12]

0.75 ... 25 mm²

[AWG 19 ... 4]

2-wire, same cross-section

Rigid

0.2 ... 1.5 mm²

[AWG 24 ... 16]

0.75 ... 10 mm²

[AWG 19 ... 8]

Flexible

0.2 ... 1.5 mm²

[AWG 24 ... 16]

1 ... 4mm²

[AWG 18 ... 12]

Flexible with end sleeve, without plastic

sleeve

0.25 ... 0.75 mm²

[AWG 24 ... 19]

0.75 ... 4 mm²

[AWG 19 ... 12]

Flexible with TWIN end sleeve and plastic

sleeve

0.5 ... 2.5 mm²

[AWG 20 ... 14]

0.75 ... 4 mm²

[AWG 19 ... 12]

Tightening torque

0.5 ... 0.6 Nm

[4.4 ... 5.3 lb-in]

3 Nm

[26.6 lb-in]

Conductor cross-section for copper cable (Cu)

for UL market

AWG 10 ... 4

Solid or stranded with ferrules

Conductor cross-section for copper cable (Cu)

for CSA market

AWG 8 ... 4

Compact stranded

Summary of Contents for SENTRON PAC2200



































































































































Search results

Summary of Contents for SENTRON PAC2200

Reviews:

Siemens SENTRON PAC2200, Product Manual, Page: 90 / 130

Search results

Summary of Contents for SENTRON PAC2200

Reviews: