Siemens SENTRON PAC2200 Product Manual Download Page 85

Page: 85 / 130

PAC2200
Equipment Manual, 12/2019, L1V30415167B-03

Technical specifications

8.1

Technical specifications

Device configuration

●

1 optically isolated digital input

●

1 optically isolated digital output

●

1 Ethernet interface, for connecting and configuring to the PC or network (optional)

●

1 M-Bus connection for reading out the measured values (optional)

●

1 RS485 port for readout and configuration (optional)

Measurement

Only for connection to AC voltage systems

Measuring method
For voltage measurement

True root-mean-square measurement (TRMS)

For current measurement

True root-mean-square measurement (TRMS)

Measured value acquisition
Energy

Contiguous (zero blind measuring)

Current, voltage

Contiguous (zero blind measuring)

Waveform

Sinusoidal or distorted

Frequency of the relative fundamental

50 / 60 Hz

(MID devices only 50 Hz)

Measured value acquisition mode

Automatic mains frequency acquisition

Summary of Contents for SENTRON PAC2200



































































































































Search results

Summary of Contents for SENTRON PAC2200

Reviews:

Siemens SENTRON PAC2200, Product Manual, Page: 85 / 130

Search results

Summary of Contents for SENTRON PAC2200

Reviews: