Siemens SENTRON PAC2200 Product Manual Download Page 81

Page: 81 / 130

PAC2200
Equipment Manual, 12/2019, L1V30415167B-03

Service and maintenance

7.1

Cleaning

Clean the device as required. Use a dry cloth for this.

NOTICE
Damage due to detergents
Detergents can damage the device. Do not use detergents.

7.2

Calibration

The device has been calibrated by the manufacturer before shipping. Recalibration is not

required provided the environmental conditions are maintained.

7.3

Firmware updates

The PAC2200 supports firmware updates.
An operating system update can be carried out on MID-approved devices.
When updating, always use the latest version of the configuration software SENTRON

powerconfig. For update instructions, please see the related documentation and the online

help for the configuration software. The last devices settings made remain unchanged.

Summary of Contents for SENTRON PAC2200



































































































































Search results

Summary of Contents for SENTRON PAC2200

Reviews:

Siemens SENTRON PAC2200, Product Manual, Page: 81 / 130

Search results

Summary of Contents for SENTRON PAC2200

Reviews: